Is your Sanyo TV not turning ON? Don’t worry, we have got you covered.
To turn ON your Sanyo TV, you can try disconnecting all external devices connected to Sanyo TV, place your Sanyo TV in a well-ventilated place, look for power problems, do a factory reset or contact Sanyo Service Centre.
This guide will walk you through a series of solutions to fix the Sanyo TV’s turning-off issue.
Why Sanyo TV won’t turn ON?
Here are a few of the reasons why your Sanyo TV is not turning ON.
- Defective devices connected to your TV
- Power supply issue due to damaged power cord, power outlet or
- Issue with TV Remote
- Virus in TV
- Motherboard issue
- Internet issue
Why Won’t My Sanyo TV Turn on But Red Light Is On?
If your Sanyo TV won’t turn on, but you see a solid or blinking red indicator light, you most likely have a power supply or other hardware issue on your hands. You might have luck unplugging your TV for 5 to 10 minutes and then plugging it back in.
If power-cycling doesn’t work, check to see if your device is still under warranty. If you still have coverage, reach out to the manufacturer to receive support.
How Do I Reset My Sanyo TV if It Won’t Turn On?
Even if you don’t have access to the Sanyo settings on your TV, unplugging and plugging your device back in functions as a way to reboot your TV.
You can also use your remote control to reboot your TV or the pinhole or reset button to factory reset it.
How to Fix “Sanyo TV won’t turn ON”?
There are a number of proven tech tips that can help you in turning ON the Sanyo TV.
It’s best to work through them in the order listed below as these solutions are organized from simplest and quickest to more complex and lengthy.
Fix 1: Restart the Sanyo TV
Most of the issues with Sanyo TVs can be fixed by restarting the TV. So, as a first step, just restart the TV.
- Unplug your TV to drain the power
- Press the physical power button on your TV. On some Sanyo TV models, this button appears on the bottom or back of the device. Press the power button on your device for as long as the user manual says.
- Then plug the TV back in and try to turn it on.
Fix 2: Disconnect the external devices connected to Sanyo TV
If any external devices such as USB, laptops, etc. are connected to your Sanyo TV, then disconnect the cables of these external devices from your TV.
When there are no external devices connected to the TV, restart the Sanyo TV.
Follow the below steps to do it.
- Unplug the TV cable from the power outlet.
- Wait for 30 seconds.
- Plug it back then.
- Turn the TV back on using the Power button.
Fix 3: Check the power supply to Sanyo TV
Check whether your power cord is broken or damaged. If it is broken, then you need to replace it.
If it is working fine, then you need to check the power outlet. If there is low power, then your TV will keep turning off.
To check the power outlet, you can connect some other device to the same power outlet and check whether it is working fine.
You can also try connecting your Sanyo TV to a different power outlet and check whether the random turn-off issue is now resolved.
If you are using a Surge protector, check whether it is faulty or not. To check this, you need to plug the TV cord directly into the outlet. If the Sanyo TV is working fine, then you need to replace or repair your Surge protector.
Note: Make sure to use a certified HDMI cable. If you use an uncertified HDMI cable, the screen may be black, or a connection error may occur.
Fix 4: Check the TV Remote
Sometimes, the TV remote will send signals to automatically turn ON and OFF your TV at random intervals.
It’s usually because your remote batteries are low. Remotes are known to send off some weird signals when they’re on the last bit of juice.
Your TV could be interpreting infrared noise from your remote as an “OFF” command. So, you can replace your battery on the TV remote to check the issue still persists.
Unplug your Sanyo TV, remove the remote batteries, and wait 5 seconds before reseating them. Sometimes the act of removing and reinserting the batteries can fix an unresponsive remote. To cover your bases, you could also swap the batteries with a new set.
You also need to check the power button on the remote. Sometimes, it could be stuck.
Fix 5: Provide proper ventilation for Sanyo TV
Your TV may overheat and stop working if there is poor ventilation and airflow. In that scenario, you can take the following actions:
- Turn off your TV.
- Using a dry microfiber towel, clear the TV’s back of all dust.
- Check to make sure nothing is obstructing the TV vents, as this could limit airflow and cause overheating.
Fix 6: Carry out a factory reset of your Sanyo TV
If none of the above techniques work out, you can do a factory reset of your Sanyo TV.
When you do a factory reset, all of the TV’s software will be restored to the state when it left the factory.
Look for a reset button or pinhole on the back of the device and hold it down according to the manufacturer’s instructions.
Fix 7: Contact Sanyo TV support
Sometimes, the issue might be with the Sanyo motherboard or with a faulty capacitor or something else. Unless you have technical skills, you cannot repair it.
In this case, it is better to report the issue to the Sanyo Service Center. Once you have reported the issue, you will get help from trained technicians.
If your TV is under warranty, you might also get it repaired free of cost.
Fix 8: Buy a new TV
If none of the above techniques works out, then it is better to buy a new Smart TV. This time, go for a different brand.
Summing up, if your Sanyo TV won‘t turn ON :
- Restart the TV
- Check if the socket is faulty and if the TV starts to work in another socket.
- Check the power cord cable for any damage or cuts.
- Carry out a factory reset
- If the issue still persists, contact Sanyo Service Centre and let the experts handle your TV.
If you are under warranty, the manufacturers will cover the repair costs or will give you a new TV.
In case the repair cost supersedes the purchase cost, consider buying a new TV rather than attempting to bring life back inside an old TV. All the best to get your Sanyo TV up and running!